11/28/2023 0 Comments Gorilla wood gluePainting – Gorilla Wood Glue can be sanded and painted. What is the Dry Color?– Gorilla Wood Glue dries a natural translucent tan color, without an orange after-glow. If necessary, shake vigorously to restore to original consistency. If the glue is frozen, thaw at room temperature. Gorilla Wood Glue will not harden in the bottle as long as the cap is closed and water is not allowed to evaporate from the bottle. To extend shelf life, keep the container sealed and stored at 55☏-75☏. To remove Gorilla Wood Glue from hands, wash with warm soap and water. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. Soak hands and skin in soap and warm water, wash, then rinse.Ĭleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. Wash hands, skin and damp cloths in soap and warm water, then rinse.Ĭlean up when glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from surface, then sand as needed. When areas have completely dried, sand as needed. Make as many passes as needed with the clean area of the cloth to remove all the glue. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood.Ĭure Time (amount of time for glue to reach total bonding strength): 24 hoursĬlean up while glue is wet: Use a clean, damp cloth to wipe off excess glue. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied.Ĭlamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The technique and type of clamp to be used is determined by many factors: the specific type of joint, type of stock or lumber, moisture content of stock, room temperature, assembly time and surface quality. 1 fluid ounce will cover approximately 1.6 square feet. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Rub together with the other surface to distribute the glue evenly on both surfaces. On hard-to-glue woods, apply the glue on both surfaces. In general, apply a generous amount of glue on one of the surfaces. Just how much Gorilla Wood Glue to apply depends on many factors. Also, be careful to avoid burnishing and end snipes. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Easy clean up with water.For best results, it is essential that the wood surfaces are prepared prior to application of glue. Easy to use – it’s a non-toxic, water-based, solvent free polyvinyl acetate (PVA).Say goodbye to the “orange after-glow” from yellow glues. Only natural wood fibres are used for a natural looking bond line. Dries natural colour – there are no added dyes. Versatile – good for use on hardwoods, softwoods, and wood composites.Use indoors or outdoors – passes ANSI/HPVA Type II water resistance.Complete projects faster – requires only 20-30 minutes of clamp time, and is fully cured in 24 hours.Gorilla strength delivered, again! Gorilla Wood Glue is a leader in strength, providing an unmatched confidence level for success.Gorilla Wood Glue is sure to be a favourite. Gorilla Wood Glue is what woodworkers, carpenters and hobbyists have been waiting to use, for their toughest jobs on planet Earth. Your wood glue just got a lot tougher! What’s more, our special formula was created for a variety of wood surfaces, is water-resistant, and has no dyes for a better looking bond line. New Gorilla Wood Glue bonds stronger and faster for wood-to-wood applications.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |